Release Notes for 3.1.8(SEb) -- Sipura Phone Adapter

SPA-1001 -- 1 Port FXS, 1 Ethernet Interface

Copyright (C) 2003-2005 by Linksys, a Division Of Cisco Systems

* * * * * * * * * * IMPORTANT * * * * * * * * * * * * * * * *  *
* Use of Proprietary Information and Copyright Notice:         *
* This release note document contains proprietary information  *
* that is to be used only by Sipura Technology customers.      *
* Any unauthorized disclosure, copying, distribution, or use   *
* of this information is prohibited. This restriction includes * 
* ALL Internet based discussion forums, e.g. DSLreports.       *
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *  *


Bug Fixes
==================================
-- since 3.1.5 --
.   Line 2 <Sticky 183> setting does not work

.   Messages with blank lines only received at any <SIP Port> may be mistaken as
    the last received message at any SIP Port

.   SPA uses 127 as the payload type for AVT tone if the inbound INVITE
    (from caller) does not include "a=rtpmap:101 telephone-event"
    in the SDP

.   Enabling/Disabling Distinctive Ringing, CID and CWCID using *code
    does not take effect until is unit is rebooted.

.   If valid number is shorter than a feature dial pattern, feature dial
    pattern may be falsely triggered. For example, if dailed number is 0
    and feature dial contains *70, then *70 can be matched and 0 cannot be
    dialed out

.   URL/IP specified in speed dial does not work

.   If inbound INVITE does not have contact header, SPA will
    send 400, but followed by 100, and 180 which is incorrect

.   If WWW-Authenticate or Authenticate header in 401/407 response 
    contains unknown parameter, such as xyz="some value", then
    the SPA may ignore the response as a bad message.


====================================    
Feature Enhancement
====================================
-- since 3.1.5 --
.    Forced RTP Port Number to be even number in SDP even when <RTP Port Min>
     and <EXT RTP Port Min> is set to odd number (accidentally)

.    Change default value of <SIP Remote-Party-ID> to "yes".

.    Discover the WAN side IP change through Keep-alive message VIA header.
     If there is a change, force SPA to re-register to proxy. 

.    Fixed DTMF caller-id for Netherland phones: 
     Increased polarity reversal post delay to 240 ms before sending
     1st dtmf digit. Use '#' as end digit for Denmark only, 
     use 'D' as start digit for ETSI only.

.    Change <Daylight Saving Time Rule> default to new US default:
     start=4/-1/7;end=10/1/7;save=1

.    Added <Voice Mail Server> parameter for Line 1/2. It takes a
     host name with optional port number (like <Proxy>). If port number
     is not specified, 5060 is used. If parameter is not blank, the
     SPA will send a one-time SUBSCRIBE to messagey-summary event
     package to the given host.

.    If a renewal REGISTER is sent to an address different from the last
     REGISTER, the SPA will not include preemptive credentials until
     it is challenged 

.    Added Swedish Features

  	A. Sweden Mid-call Feature
  	How to turn on Sweden CW/CFWD/CONF feature
	   - [Regional]<Feature Invocation Method> = Sweden. 
	   - [Regional]<Feature Invocation Tone> = 350@-16;*(.1/.1/1)
	   - [Regional]<Hook Flash Timer Min> = 0.05

	  B. Redial Feature
	    -[Line1/2]<Call Redial Serv> = Yes
	    -[Regional]<Call Redial Code> = *07
	  User can press *07 to re-call the last outgoing call.
  
	  C. Call Back Busy Feature
	    -[Line1/2]<Call Back Serv> = Yes
	    -[Regional]<Call Back Busy Act Code> = *05
	  User can enableds the call back service when encountering a busy 
	  destination. SPA will reattempt the last made call every 
	  <Call Back Retry Intvl> in .

	  D: Services Announcement
	    -[Line1/2]<Service Announcement Serv> = Yes
	    -[Regional]<Service Annc Base Number> = {announcement server base number}
	    -[Regional]<Service Annc Extension Codes> = {SAEC Script}
  

.    Change <VMWI Ring Splash Len> default to 0 (from 0.5s)

.    Let speed dial entries go through dial plan

.    If SPA receives an INVITE to itself while it is sending
     an INVITE (to start a new call), SPA will respond 486 instead
     of 405.

.    Support Danish VMWI signaling

.    Ignore peer INVITE/ACK without SDP if call is already connected